Fire Alarm & Fighting

The gas Detector Is designed for single station use.Small and compact, small commercial properties, and recreational vehicles. It is intended to detect leakage of natural gas (methane gas), town gas, and bottled gas (propane gas).

• The detector is designed for 9 to 32 Volts D.C.to install in major of fire alarm panels, The gas Detector can be set high (for methane gas) or low (for propane (LPG) gas).
• Detect all sorts of combustible gases, natural gas (methane), bottled gas (propane), LPG (Liquefied petroleum Gas), LNG (Liquefied natural gas),coalgas,including town gas.
• Easy toinstall,mounting bracket included.
• Highquality durablesensor.
• Self diagnostic functionby MCUintelligent software.
• Excellentreliability & High stability.
• Idealfor allkitchens.

HST Fire Alarm System

Description & Features
• This Conventional8’Bell very low power consumption
• Standard: 8 inch
• Rated Voltage:24V
• Rated current: 1OmA
• Sound:89dB/3m(A)
• Material: aluminium
• Temperature:1•0 to 60
• Humidity: s930

HST Fire Alarm System

Description & Features
• This Conventional Siren very low power consumption
• Rated Voltage:24Volt
• Rated current:SOmA
• Sound:89dB/3m(A)
• Material: Fire Proof Plastic
• Temperature:-10 to 60
• Humidity:930

HST Fire Alarm System

Description & Features

• This detector uses a very High Sensitivity UV Filter to Detect the Fast flame fires.
• Highly reliable, long lifeUV receptor tube.
• Low power consumption.
• HD104U can be Intermixed with other types of Detection on the panel’s detection circuitry.
• Easily maintained: cleaning can be accomplished Without disassem­

bling the detector.

• This detector is designed to be used with most conventional fire alarm controlpanelwhere ills can work from 9Volt to 32V D.C.
• Itishas Two Led’s on each detector to provide local sso•viewing alarm

indication.

• This detector support ExternalRemote indication LED.

HST Fire Alarm System

Description & Features
• Operating Temperature •1o•c to so•c
• Operating Humidity 0 to 95 RH,
• No condensation or Icing

• Operating Voltage 22VDC to 30VDC
• Average Current 70 mA
• Light Output 1.2 WS
• Flash Rate 2 seconds
• Sound Level 1OOdB
• Light Life 30000 flashes

HST Fire Alarm System

Description & Features

• This Conventional Fixed & Rate of rise Heat Sensor use a thermal sensing Element to detect
• This detector is designed to provide open area protection and to be used with most conventional fire alarm controlpanel where It is can work from 9Volt to 32V D.C.
• It is has Two Led's on each detector to provide local360° viewing alanm indication.
• It is flash every five seconds Indicating that power is applied and the detector is working properly.
• The Led's latch on In alarm.Led's will be off when a trouble condition exists indicating that the detector sensitivity is outside the listed limit. The alanm can be reset only by a momentary power interruption.
• This detector support ExternalRemote Indication LED

HST Fire Alarm System

Description & Features
• The HC102 is a Conventional call-point based upon our industry
standard series housing and features easy to install, push•fit wiring terminals.
• The unit can support either a ‘Frangible Glass’ element or a ‘Non
Frangible Plastic’ element.
• Push in and Pull Down Call point
• Can be reset by Key
• Red colour
• Fire proof materials
• 470 Ohm Resistance
• Modern style Call Point

HST Fire Alarm System

HD101-MINI- hst -fire(Mini smoke detector)

Operating Vohage
Range
9 to 28 VDC Volts Non-polarized
Standby Current “120 A@24VDC
Maximum Alarm Current
(LED on) “20mA@24VDC
Operating Temperature
Range “95%RH(40°C±2°C) Relative Humidity, Non-condensing
Operating Humidy
Range -1o•c to so•c (14•F to 122•F)
Smoke Alarm Sensit1v y 1.06±2B T
Temperature Alarm
Sensitivit 5?-C (135.F)A1R (only for with heat
sensor)
Height 42 mm installed in Base
Diameter 64 mm

HST Fire Alarm System

• Range 9 to 28 VDC Volts Non•polarized.
• Standby Current 120.A@24VDC.
• Maximum Alarm.
• Current (LED on) 20m.A@24VDC.
• Operating Humidity.
• Range 95%RH(40•c:t2•CJ Relative Humidity,
  Non•condensin.
• Operating Temperature.
• Range -1o•c to so•c (14•F to 122•F).
• Smoke Alarm Sens iv y 1.06:t.26%FT.
• Temperature Alarm.
• Sens ivity 5?-C (135.F) A1R (only for with heat
  sensor).
• Height 42 mm nstalled in Base.
• Di ameter 64mm.

Fire

• The HS104 is a ConventionalRemote Indication LED which connect to detector to show the alarm conditions with high bright Red Colour LED
• Option white or red color cover
• Support European and USA standard at the same
• Modem Style

HST Fire Alarm System